Zilog Standalone Programmer 2.3.0 (Build 21092402)
==============================================================================
    Contact Information
    --------------------------------------------------------------------------
      Zilog Inc. Web Site: 
         http://www.zilog.com
         
      Technical Support Channel: 
         https://www.zilog.com/index.php?option=com_product&task=tech_support&Itemid=88

    Table of Contents
    --------------------------------------------------------------------------
        A. CHANGES FROM PREVIOUS RELEASES
        B. COMPATIBILITY
        C. SYSTEM REQUIREMENTS
        D. APPLICATION AND OTHER OS ISSUES
        E. P & L (PRECAUTIONS AND LIMITATIONS)
        F. CLOSED CHANGE REQUESTS
        G. OPEN CHANGE REQUESTS
        H. OTHER OPEN ISSUES


A. CHANGES FROM PREVIOUS RELEASES
==============================================================================

    (to 2.3.0 Build 21092402)
    - Added support for programming Encore! Z8F6482 RevAD (and subsequent)
      target devices that disable the FLL after power on reset (POR).  Erasing
      and/ or programming Z8F6482 targets requires the FLL to be enabled and 
      the DCO to be configured to generate a SYSCLK frequency of at least 1MHz.
      Refer to the “Z8 Encore! XP F6482 Series Product Specification” (PS0294)
      for more information.
    - Replaced the ZSP Boot Loader with the Zilog DFU Boot Loader

    (to 2.2.0 Build 20081704)
    - Fixed programming issue for Z8Encore! 8-pin devices.
    - Added support for Z8Encore! ZMOTION devices: 
      Z8F1681xK_2247, Z8F1681xN_2247, Z8F6481xN_2247, Z8F3224xH_2258, 
      Z8F3224xK_2258, and Z8F3224xN_2258 
    - Grouped Z8Encore! ZMOTION devices under the “Z8Encore_ZMOTION_Series” Series.
    
    (to 2.1.1 19082003)
    - Added a prompt to erase the ZSP Configuration Information Area on firmware
      upgrading if the ZSP firmware version is v2.0 or earlier.
    - Fixed the issue of programming S3 Smart Options.
      
    (to 2.1.0 Build 19060301)
    - New features added in v2.1.0 of the ZSP Configuration Software require 
      a ZSP firmware upgrade to version v2.1 (or later)

        *** BEFORE UPGRADING THE ZSP USB FIRMWARE TO v2.1 (OR LATER), THE ZSP 
            CONFIGURATION AND IMAGE AREA MUST BE CLEARED (ERASED) USING THE ZSP
            CONFIGURATION SOFTWARE. ZSP FIRMWARE v2.0 (OR EALRIER) CONFIGURATION 
            INFORMATITON IS NOT COMPATIBLE WITH FIRMWARE VERSION v2.1 (OR LATER) 
            CONFIGURATION INFORMATION. SIMILARLY THE ZSP CONFIGURATION AND IMAGE 
            AREA MUST BE CLEARED (ERASED) PRIOR TO DOWNGRADING ZSP v2.1 FW ***

    - Added password-protection (PW) of select ZSP operations 
    - New security feature to limit the number of target devices that can be 
      programmed using the ZSP via a configurable program counter (PC). 
    - Added new Advanced view to configure PW and PC settings

    (to 2.0.0 Build 19021403)
    - Added Z8Encore! MCU Family
    - New Firmware 2.0 and Bootloader 2.0

B. COMPATIBILITY
==============================================================================
    Devices
    --------------------------------------------------------------------------
    S3 MCU Family
    Z8Encore MCU Family

    ZSP Driver
    --------------------------------------------------------------------------
    USB device drivers can be found  in the following location:

          <ZDS installation>\Device Drivers\USB\

          ******************** Important! ***************************
          The Device Driver installer need to be run as Administrator
    
C. SYSTEM REQUIREMENTS
==============================================================================
    Supported Operating Systems (Validated)
    --------------------------------------------------------------------------
      Windows  7 32 and 64-bit
      Windows  8 32 and 64-bit
      Windows 10 32 and 64-bit

    ZSP Firmware
    --------------------------------------------------------------------------
    Please refer to the ZSP_Upgrade_Information.pdf located  in  the following
    directory for information:

          <ZDS installation>\bin\firmware\ZSP


D. APPLICATION AND OTHER OS ISSUES
==============================================================================
   1.  Apply the latest Windows updates to the host system when appropriate.

E. P & L (PRECAUTIONS AND LIMITATIONS)
==============================================================================
   TBD

F. CLOSED CHANGE REQUESTS
==============================================================================
   NONE

G. OPEN CHANGE REQUESTS
==============================================================================
   NONE

H. OTHER OPEN ISSUES (NOT RECORDED AS CHANGE REQUESTS)
==============================================================================
   NONE